Strain induced strengthening of soft thermoplastic polyurethanes under cyclic deformation

We investigate the cyclic mechanical behavior in uniaxial tension of three different commercial thermoplastic polyurethane elastomers (TPU) often considered as a sustainable replacement for common filled elastomers. All TPU have similar hard segment contents and linear moduli but sensibly different large strain properties as shown by X-ray analysis. Despite these differences, we found a stiffening effect after conditioning in step cyclic loading which greatly differs from the common softening (also referred as Mullins effect) observed in chemically crosslinked filled rubbers. We propose that this self-reinforcement is related to the fragmentation of hard domains, naturally present in TPU, in smaller but more numerous sub-units that may act as new physical crosslinking points. The proposed stiffening mechanism is not dissimilar to the strain-induced crystallization observed in stretched natural rubber, but it presents a persistent nature. In particular, it may cause a local reinforcement where an inhomogeneous strain field is present, as is the case of a crack propagating in cyclic fatigue, providing a potential explanation for the well-known toughness and wear resistance of TPU.     

Effect of additive length and chemistry on the morphology of blends of conjugated thiophenes and fullerene derivative acceptor molecules

Small molecule additives have been shown to increase the device efficiency of conjugated polymer (donor) and fullerene derivative (acceptor) based organic solar cells by modifying the morphology of the device active layer. In this paper we conduct a systematic study of how additives affect the donor‐acceptor morphology using molecular dynamics simulations of blends of thiophene‐based oligomers, mimicking poly(3‐dodecylthiophene) (P3DDT) or poly(2,2′:5′,2”‐3,3”‐didocyl‐terthiophene) (PTTT), and fullerene derivatives with additives of varying length and chemical functionalization, mimicking experimentally used additives like methyl ester additives, diiodooctane, and alkanedithiols. We find that functionalization of additives with end groups that are attracted to acceptor molecules are necessary to induce increased donor‐acceptor macrophase separation. In blends where acceptors intercalate between oligomer alkyl side chains, functionalized additives decrease acceptor intercalation. Functionalized additives with shorter alkyl segments increase acceptor macrophase separation more than additives with same chemical functionalization but longer alkyl segments. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1046–1057     

显微动态图像分析技术及其在生物物理中的应用

介绍了一种可实时监测细胞生命活动的显微动态图像分析技术。该技术把显微光学成像技术、数字处理技术和动态图像分析技术结合为一体,可实现对活细胞的结构功能、生长过程和环境变化的影响等进行非侵入性连续监测。通过在细胞膜弹性模量测量中的应用表明,该技术不仅原理可靠,实现容易,应用方便,而且检测速度快,测量精度高,稳定性能好。此项技术可望在生物物理学的实验研究中获得广泛的应用。     

利用CCD光电测量系统测量杨氏弹性模量

提出一种测量微小伸长量的光电测量方法,即利用CCD光电测量系统将单缝衍射的光强分布转换为电信号,经过计算机处理后输出光强分布曲线,从相邻波谷读出衍射条纹间隔,通过软件的简单操作直接输出测量结果.实现了数据采集及运算结果的实时化、半自动化,并克服了传统方法的测量困难和数据处理的复杂计算.利用这一方法测定了钢丝的杨氏弹性模量,与标称值符合得较好.     

Preservation of Lipschitz constants by Bernstein type operators

Summary We obtain preservation inequalities for Lipschitz constants of higher order in simultaneous approximation processes by Bernstein type operators. From such inequalities we derive the preservation of the corresponding Lipschitz spaces.     

WEIGHTED APPROXIMATION ON SZASZ—TYPE OPERATORS

In this paper, we use weighted modules ω(?)(f,t)w to study the pointwise approximation on Szasz-type operators, and obtain the direct and converse theorem, as well as characterizations of the pointwise approximation of Jacobi-weighted Szasz-type operators.     

Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Amine‐cured epoxy/clay nanocomposites. II. The effect of the nanoclay aspect ratio

The thermophysical and mechanical properties of a nanocomposite material composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay are reported. The storage modulus at 100 °C, which was above the glass‐transition temperature (T_g), increased approximately 350% with the addition of 10 wt % (6.0 vol %) of clay. Below the T_g, the storage modulus at 30 °C increased 50% relative to the value of unfilled epoxy. It was determined that the T_g linearly increased as a function of clay volume percent. The tensile modulus of epoxy at room temperature increased approximately 50% with the addition of 10 wt % of clay. The reinforcing effect of the organoclay nanoplatelets is discussed with respect to the Tandon–Weng and Halpin–Tsai models. A pseudoinclusion model is proposed to describe the behavior of randomly oriented, uniformly dispersed platelets in nanocomposite materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4391–4400, 2004     

Vacations in GI X/M Y/1 systems and Riemann boundary value problems

We consider systems of GI/M/1 type with bulk arrivals, bulk service and exponential server vacations. The generating functions of the steady-state probabilities of the embedded Markov chain are found in terms of Riemann boundary value problems, a necessary and sufficient condition of ergodicity is proved. Explicit formulas are obtained for the case where the generating function of the arrival group size is rational. Resonance between the vacation rate and the system is studied. Complete formulas are given for the cases of single and geometric arrivals. This revised version was published online in June 2006 with corrections to the Cover Date.     

Forced-air precooling of spherical foods in bulk: A parametric study

In this paper, a mathematical model for forced-air precooling of spherical food products in bulk is developed. The foods are arranged in horizontal layers stacked one above the other to form a rectangular parallelepiped with a vertical gap in between the product layers. The foods are cooled by chilled air blown along the height of the package. The governing equations for the conduction heat transfer in the foods, simultaneous heat and mass transfer at the food-air interface and in the air stream are solved numerically using finite-difference methods. A comprehensive numerical study is performed by varying the process parameters over a wide range. Typical results showing the variation of moist air properties along the height of the package and the effect of each parameter on the process time are presented. The ranges of parameters for advantageous operation of the precooling system are identified. Correlations are obtained for the process time based on the product center and mass-averaged temperatures in terms of process parameters.